This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
configuration:wlan-client-bridge [2018/03/20 14:59] juraschek [WLAN Client Bridge] |
configuration:wlan-client-bridge [2022/01/03 12:39] schmitt |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== WLAN Client Bridge ====== | ====== WLAN Client Bridge ====== | ||
- | To bridge a WLAN Client connection with a Ethernet LAN there are some requierments needed. | ||
- | The Wifi Access Point need to Support the 4 Address Frame, which the AP in Netmodule Router does. | ||
- | This Funtionality was introduced with the NRSW 4.1.0.100 so please use the current Version: [[ftp://share.netmodule.com/router/public/system-software/4.1/4.1.0.100/|4.1.0.100]] | + | To bridge a WLAN Client connection with a Ethernet LAN there are some requirements needed. |
+ | The WiFi Access Point as well as the WiFi clients need to support 4 Address Frame. The configurtion is only possible with the following products: | ||
- | <WRAP center round important 80%> | + | * NB1800 |
- | In the DUAL Mode will only see SSID that are sending on the channel the AP is configured to | + | * NB1810 |
- | </WRAP> | + | * NB2700 |
+ | * NB2710 | ||
+ | * NB2800 | ||
+ | * NB2810 | ||
+ | * NB3700 | ||
+ | * NB3701 | ||
+ | * NB3710 | ||
+ | * NB3711 | ||
+ | * NB3800 | ||
+ | |||
+ | Please use the current Version: [[https://share.netmodule.com/public/system-software/4.3/4.3.0.106/|4.3.0.106]]. This funtionality was introduced with the NRSW 4.1.0.100. | ||
+ | In case you running a NB800 or NB1601 you can take a look at our [[configuration:mesh-network|Mesh Network]] funtionality | ||
Line 17: | Line 27: | ||
- | {{ :configuration:screenshot_-_07032017_-_03_54_52_pm.png?nolink |}} | + | {{ :configuration:wlan_ap.png?nolink |}} |
- | {{ :configuration:screenshot_-_07032017_-_03_54_42_pm.png?nolink |}} | + | {{ :configuration:wlan_conf.png?nolink |}} |
At the IP Settings Page please enable the "4addr frame" and choose the LAN Interface you want to bridge with. | At the IP Settings Page please enable the "4addr frame" and choose the LAN Interface you want to bridge with. | ||
- | {{ :configuration:screenshot_-_07032017_-_03_54_32_pm.png?nolink |}} | + | {{ :configuration:wlan_ip_settings.png?nolink |}} |
- | ===== Client Config Config ===== | + | ===== Client Config ===== |
Please configure your WLAN Client Connection as usual | Please configure your WLAN Client Connection as usual | ||
- | {{ :configuration:screenshot_-_07042017_-_05_25_55_pm.png?nolink |}} | + | {{ :configuration:wlanclient_admin.png?nolink |}} |
- | {{ :configuration:screenshot_-_07042017_-_05_26_04_pm.png?nolink |}} | + | {{ :configuration:wlanclient_conf.png?nolink |}} |
- | {{ :configuration:screenshot_-_07042017_-_05_26_10_pm.png?nolink |}} | + | {{ :configuration:wlan_client.png?nolink |}} |
- | {{ :configuration:screenshot_-_07042017_-_05_26_18_pm.png?nolink |}} | + | {{ :configuration:wlanclient_ipset.png?nolink |}} |
+ | |||
+ | ==== Activating the CLient Bridge ==== | ||
After the WLAN Connection is set up. Please go to Interfaces->Link Managment and edit your WLAN Connection | After the WLAN Connection is set up. Please go to Interfaces->Link Managment and edit your WLAN Connection | ||
Line 40: | Line 53: | ||
{{ :configuration:screenshot_-_07042017_-_05_26_29_pm.png?nolink |}} | {{ :configuration:screenshot_-_07042017_-_05_26_29_pm.png?nolink |}} | ||
{{ :configuration:screenshot_-_07042017_-_05_26_40_pm.png?nolink |}} | {{ :configuration:screenshot_-_07042017_-_05_26_40_pm.png?nolink |}} | ||
+ | |||
+ | ---- | ||
+ | ===== Other HowTos ===== | ||
+ | [[configuration:mesh-network|Mesh Network]] | ||
+ | |||