Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
configuration:wlan-client-bridge [2020/06/04 05:05]
dodenhoeft [WLAN Client Bridge]
configuration:wlan-client-bridge [2022/01/03 12:57] (current)
schmitt
Line 1: Line 1:
 ====== WLAN Client Bridge ====== ====== WLAN Client Bridge ======
  
-To bridge a WLAN Client connection with a Ethernet LAN there are some requierments needed. ​ 
-The Wifi Access Point need to Support the 4 Address Frame, which the AP in Netmodule Router does. 
  
-  * NB1800 - NB1810 +To bridge a WLAN Client connection with a Ethernet LAN there are some requirements needed. ​ 
-  * NB2700 - NB2710 +The WiFi Access Point as well as the WiFi clients need to support 4 Address Frame. The configurtion is only possible with the following products: ​
-  * NB2800 - NB2810 +
-  * NB3700 - NB3701 - NB3710 - NB3711 +
-  * NB3800 - +
  
-This Funtionality was introduced with the NRSW 4.1.0.100 so please ​use the current Version: [[ftp://​share.netmodule.com/router/​public/​system-software/​4.1/4.1.0.100/​|4.1.0.100]]+  * NB1800 
 +  * NB1810  
 +  * NB2700 
 +  * NB2710  
 +  * NB2800 
 +  * NB2810 
 +  * NB3700 
 +  * NB3701 
 +  * NB3710 
 +  * NB3711  
 +  * NB3800 
 + 
 +Please ​use the current Version: [[https://​share.netmodule.com/​public/​system-software/​4.3/4.3.0.106/|4.3.0.106]]. This funtionality was introduced with the NRSW 4.1.0.100
 +In case you running a NB800 or NB1601 you can take a look at our [[configuration:​mesh-network|Mesh Network]] funtionality ​
  
  
Line 19: Line 27:
  
  
-{{ :​configuration:​screenshot_-_07032017_-_03_54_52_pm.png?nolink |}} +{{ :​configuration:​wlan_ap.png?nolink |}} 
-{{ :​configuration:​screenshot_-_07032017_-_03_54_42_pm.png?nolink |}}+{{ :​configuration:​wlan_conf.png?nolink |}}
  
 At the IP Settings Page please enable the "4addr frame" and choose the LAN Interface you want to bridge with. At the IP Settings Page please enable the "4addr frame" and choose the LAN Interface you want to bridge with.
  
-{{ :​configuration:​screenshot_-_07032017_-_03_54_32_pm.png?nolink |}}+{{ :​configuration:​wlan_ip_settings.png?nolink |}}
  
  
Line 31: Line 39:
 Please configure your WLAN Client Connection as usual Please configure your WLAN Client Connection as usual
  
-{{ :​configuration:​screenshot_-_07042017_-_05_25_55_pm.png?nolink |}} +{{ :​configuration:​wlanclient_admin.png?nolink |}} 
-{{ :​configuration:​screenshot_-_07042017_-_05_26_04_pm.png?nolink |}} +{{ :​configuration:​wlanclient_conf.png?nolink |}} 
-{{ :​configuration:​screenshot_-_07042017_-_05_26_10_pm.png?nolink |}} +{{ :​configuration:​wlan_client.png?nolink |}} 
-{{ :​configuration:​screenshot_-_07042017_-_05_26_18_pm.png?nolink |}}+{{ :​configuration:​wlanclient_ipset.png?nolink |}} 
 + 
 +==== Activating the CLient Bridge ==== 
  
 After the WLAN Connection is set up. Please go to Interfaces->​Link Managment and edit your WLAN Connection After the WLAN Connection is set up. Please go to Interfaces->​Link Managment and edit your WLAN Connection
Line 40: Line 51:
 Please define your local LAN Interface to bridge with. Please define your local LAN Interface to bridge with.
  
-{{ :​configuration:​screenshot_-_07042017_-_05_26_29_pm.png?nolink |}} +{{ :​configuration:​activating_bridge1.png?nolink |}} 
-{{ :​configuration:​screenshot_-_07042017_-_05_26_40_pm.png?nolink |}}+{{ :​configuration:​activating_bridge.png?nolink |}} 
 + 
 +---- 
 +===== Other HowTos ===== 
 +[[configuration:​mesh-network|Mesh Network]]