Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
cs:installation [2019/11/01 15:06]
voegeli
cs:installation [2019/11/01 15:07] (current)
voegeli
Line 15: Line 15:
   -When prompted, log out.   -When prompted, log out.
  
-<​WRAP ​centre ​round important 60%>+<​WRAP ​center ​round important 60%>
 For generating the SSL certificate corresponding to the domain under which the machine is reachable, the Connectivity Suite uses Let’s Encrypt. Let’s Encrypt is a free, automated certificate authority. For generating the SSL certificate corresponding to the domain under which the machine is reachable, the Connectivity Suite uses Let’s Encrypt. Let’s Encrypt is a free, automated certificate authority.
  
Line 42: Line 42:
   -After changing the password, the Connectivity Suite will be ready for use.   -After changing the password, the Connectivity Suite will be ready for use.
  
- <​WRAP ​centre ​round info 60%>+ <​WRAP ​center ​round info 60%>
 Step 7-11 may need to be repeated, depending on the chosen Home Network layout in step 6. Step 7-11 may need to be repeated, depending on the chosen Home Network layout in step 6.
 </​WRAP>​ </​WRAP>​
  
-<​WRAP ​centre ​round important 60%>+<​WRAP ​center ​round important 60%>
  
 Configuring the Home Network (step 6-11) can only be done once, during the initial setup of the software! Configuring the Home Network (step 6-11) can only be done once, during the initial setup of the software!
Line 85: Line 85:
   -Plug the USB stick into your router to start the configuration update.   -Plug the USB stick into your router to start the configuration update.
   -The router will now automatically connect to the Connectivity Suite {{ :​cs:​router23.png?​ }}   -The router will now automatically connect to the Connectivity Suite {{ :​cs:​router23.png?​ }}
-<​WRAP ​centre ​round important 60%>+<​WRAP ​center ​round important 60%>
 The USB stick used to configure the NetModule router must be a FAT16/32 formatted USB stick. The USB stick used to configure the NetModule router must be a FAT16/32 formatted USB stick.
 </​WRAP>​ </​WRAP>​
Line 134: Line 134:
   -The applied uploaded configuration must now be shown in the Main dialogue box in the table.   -The applied uploaded configuration must now be shown in the Main dialogue box in the table.
  
-<​WRAP ​centre ​round info 60%>+<​WRAP ​center ​round info 60%>
 Notice: It can take several seconds until the software has been uploaded. Do not refresh the pager after the click “SAVE”. Notice: It can take several seconds until the software has been uploaded. Do not refresh the pager after the click “SAVE”.
 </​WRAP>​ </​WRAP>​
Line 145: Line 145:
   -Click “ADD” to update the router configuration. A confirmation message must pop up which confirms the deployment of the update. A confirmation message must pop up which confirms the deployment of the update.{{ :​cs:​softwareupdate26.png?​ }}   -Click “ADD” to update the router configuration. A confirmation message must pop up which confirms the deployment of the update. A confirmation message must pop up which confirms the deployment of the update.{{ :​cs:​softwareupdate26.png?​ }}
   ​   ​
-<​WRAP ​centre ​round info 60%>+<​WRAP ​center ​round info 60%>
 The option to start a deployment Job immediately is only available if the chosen Device is currently online and reachable from the Connectivity Suite. If the deployment for some reason cannot be completed within 24 hours, the Job is considered failed. The option to start a deployment Job immediately is only available if the chosen Device is currently online and reachable from the Connectivity Suite. If the deployment for some reason cannot be completed within 24 hours, the Job is considered failed.
 </​WRAP>​ </​WRAP>​
Line 151: Line 151:
 ==== Direct device access ==== ==== Direct device access ====
  
-<​WRAP ​centre ​round info 60%>+<​WRAP ​center ​round info 60%>
 For the following steps an account with Platform Administrator rights and an OpenVPN client is required. For the following steps an account with Platform Administrator rights and an OpenVPN client is required.
 </​WRAP>​ </​WRAP>​
Line 159: Line 159:
   -Establish a VPN connection using the Service Access configuration downloaded in step 1. After successful VPN connection you can now establish a connection to the End Device (e.g. via SSH) using the IP obtained from the connectivity Suite in step 3. {{ :​cs:​directaccess23.png?​ }}   -Establish a VPN connection using the Service Access configuration downloaded in step 1. After successful VPN connection you can now establish a connection to the End Device (e.g. via SSH) using the IP obtained from the connectivity Suite in step 3. {{ :​cs:​directaccess23.png?​ }}
  
-<​WRAP ​centre ​round info 60%>+<​WRAP ​center ​round info 60%>
 The Web interface of a NetModule router can be accessed directly from the Connectivity Suite UI by navigating to the page “Devices” and clicking on the button “OPEN WEB INTERFACE” in the Device details box. The Web interface of a NetModule router can be accessed directly from the Connectivity Suite UI by navigating to the page “Devices” and clicking on the button “OPEN WEB INTERFACE” in the Device details box.
 </​WRAP>​ </​WRAP>​