NetModule Router Wiki

User Tools

Site Tools

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Last revisionBoth sides next revision
configuration:qos [2016/12/20 11:30] – dotoliconfiguration:qos [2016/12/21 09:22] – dotoli
Line 1: Line 1:
 ====== QoS Quality of Service ====== ====== QoS Quality of Service ======
  
 +The ratio must not exceed 40:1 \\
 +If there is only traffic for one queue it may use the unused bandwidth of the other queues\\
 +Only the output can be configured. \\
  
-The amount of bandwith must not be higher as the available bandwith. \\ +**Bandwith: fixed (WWANX/WAN/OpenVPN) ** \\
-The ratio must not exceed 40/1 \\ +
- +
- +
-**fixed Bandwidth ** \\ +
-{{:configuration:qos_fixed_class.png?1200|}}+
 {{:configuration:qos_fixed.png?1200|}} {{:configuration:qos_fixed.png?1200|}}
- 
 example: \\ example: \\
-high: TOS (Dec) 184 = DSCP (Dec), 46 (Hex) 0x2E / for voice \\ +high: TOS (Dec) 184 = DSCP (Dec), 46 (Hex) 0x2E / for voice application\\ 
-low:  TOS (Dec) 104 = DSCP (Dec), 26 (Hex) 0x1A / for video \\+low:  TOS (Dec) 104 = DSCP (Dec), 26 (Hex) 0x1A / for video application\\
 default: All OTHER = not specified default: All OTHER = not specified
  
-ratio: 19/6/1 = 26Mbit/s bandwidth. \\  +ratio: 19:6:1 = 26Mbit/s bandwidth. This is also the interface output limit. \\ 
- +
-QoS handels the packtes only if the configured upstream bandwidth has been reached\\ +
- +
- +
-**fixed Bandwidth ** \\ +
- +
- +
- +
- +
- +
- +
- +
- +
  
-1.Set the Administrative Status to enabled \\ +The queue limits will only be enforced, if there is more data than fits through the main limit.\\
-{{:configuration:qos_administration.png?600|}} \\ +
-2.Configure the desired Bandwidth congestion: \\+
  
-**Interface**: Select the desired inteface. \\ +**Bandwidth: auto(WWANX)  ** \\ 
-**auto**:   Qos manages the bandwith according the configured priority.(1=high/10=low). \\ +IP to ping: Configure a reachable host in the internet, preferably the target host. \\ 
-IP to ping: A host is needed in order to measure the current bandwith. \\ +Based on the RTT the bandwith ratio is divided as follows: \\ 
-**fixed**:  QoS works with the configured settings. The amount of bandwith should never be higher as the available bandwith.  \\ +higest priority = 50%, \\  
-{{:configuration:add_qos_interface_.png?600|}} \\+middle priority = 45%, \\ 
 +lowest priority = 5% \\
  
-3. Service configuration \\ +**Interface: LANX** \\ 
-auto: \\ +Configure an upstream/downstream limitation without QoS.
-{{:configuration:qos_service.png?600|}} \\ +
-fixed: \\ +
-{{:configuration:qos_service_fix.png?600|}}+

Page Tools

configuration/qos.txt · Last modified: 2017/05/22 08:41 by dotoli